in Search
Untitled Page

ARCHIVED FORUM -- April 2007 to March 2012
READ ONLY FORUM

This is the first Archived Forum which was active between 17th April 2007 and 1st March February 2012

 

Browse Site by Tags

Showing related tags and posts accross the entire site.
All Tags » Repair » workbench (RSS)
  • Attyca 1 project

    My attyca 1 is in need of renovation. The bench has a scratched edge . Has anyone tried to restoring an attyca bench with a scratched edge ? Do you have any good ideas to restore the edge ? I'm thinking of putting an angled sheet of brushed aluminum or stainless steel.
    Posted to Forum by Krona on 02-19-2012
  • Front Panel Fonts

    I am working on restoring a Beomaster 1700 amp, and would like to be able to be able to repair damage to the printing on the slider controls and front panel. What fonts did B&O use in their designs, and do members have any recommendations or tips for restoring damaged front panels? It seems to be...
    Posted to Forum by ormej01 on 01-11-2012
  • Beolab 2500 - Voltage Problem

    Hi Guys, I've just joined and am starting off with problems !!! - I have inherited a pair of Beolab 2500 speakers, but they are set for 120V and not for 240V supply - I've been doing a bit of reading on this forum and there are some posts which say that the transformer can deal with both inputs...
    Posted to Forum by Crawford on 12-18-2011
  • Repairing a Beolit 707

    On the other day, i spotted a nice Beolit 707 on the auction site. I won and waited for the nice classic item to come to my hands. The seller stated that the radio was fully working. After some days it was there. Cosmetically as described (in a very very good condition i must say). Unfortunately when...
    Posted to Forum by DrDimitris on 05-29-2011
  • Beovox S45.2 cab refinish?

    I've just recently picked up a pair of S45.2's. The drivers are intact and sound great, however the cabinets (rosewood) could benefit from a bit of refinishing. Nothing major... just a little scratched and faded. Anyone have experience refinishing these? Any special precautions I should take...
    Posted to Forum by macguyft on 02-15-2011
  • Logic board (amplifier) for a Beomaster 5500

    Hi this is my first post in this forum and i hope i am posting in the right section, i was given a beosystem 5500 I am an electronics fan and loved the system at first sight, when i tried to connect everything worked except the speakers, i am a computer technician so i opened the unit and found that...
    Posted to Forum by rfarfan on 10-27-2010
  • BEOVISION MX 5500 (3251) Multiple Problems?

    Hi, I have a BEOVISION MX 5500 (3251) That is having multiple problems? I juts picked up a car load of older B&O stuff from a Beophile downsizing and this was in the mix. I live in the USA and am trying to connect the TV to an over the air Digital TV box. I have tried to connect it through the co...
    Posted to Forum by Veloseller1 on 03-09-2010
  • PSU problem on BV3/32

    I have just purchased a known defective BV3/32 for its Surround module & STB/C but am also considering a repair if if won't cost more than the TV is actually worth When you press TV the standby light goes to green but there is no sound or picture and you have to remove power lead from the set...
    Posted to Forum by richtoy on 06-14-2009
  • Need help with Beocenter AV5 will not enter the MENU

    Hallo, I need help. I bought some Beocenter AV5 from a hotel here in Stockholm where they said to me that device makers are ordinary consumer TV, s but now it appeared that it did not come in (Menu) via remote control, could someone tell me why I can not may come into menu? Are they perhaps the hotel...
    Posted to Forum by BegBeo on 05-05-2009
  • Bang & Olufsen Red Line Authentic DIY ABR (Auxiliary Bass Radiators) Successful Repair

    Design concept failure As we all know, after about 15 or so years the foam used in B&O & many other manufacturers speakers turns to mush, cones fall away, speakers become seemingly useless. A market has arisen providing a readily available supply of replacement foam rubber rings, and appropriate...
    Posted to Forum by BeoMatt on 03-11-2009
Page 1 of 2 (13 items) 1 2 Next >