in Search
Untitled Page

ARCHIVED FORUM -- April 2007 to March 2012

This is the first Archived Forum which was active between 17th April 2007 and 1st March February 2012


Browse Site by Tags

Showing related tags and posts accross the entire site.
All Tags » powerlink (RSS)
  • Using PowerLink to control nonB&O amps

    Hi I came accross something in the Beotech website ( showing how to use pin 4 in the powerlink to switch on a relay attached to a nonB&O subwoofer. I would like to do something similar until I can save up enough for some Beolab 9s, I have a BeoCenter2....
    Posted to Forum by jamescumming on 12-04-2009
  • Re: Connecting BeoSound Overture to MX7000

    Can I use both: ML/MCL MCL-2P - forstærker Ouverture -> Powerlink -> (ML/MCL or MCL - 2P) -> Five din to ? Or should I use: Ouverture -> Powerlink -> Beolink Passive -> Five din to ? Just tested the CD player! It´s so amazing. The sound is great through the MX7000!
    Posted to Forum by LarsBergen on 04-17-2009
  • Connecting BeoSound Ouverture to MX7000

    First off I have to excuse myself for asking what probably is a couple of stupid questions. I´m all new in this beoworld. 1. I was told that if I wanted to listen to the cd-player through the MX i needed to: Use my Beo4 remote Press list until AV* appeared Then press GO and the choose CD The problem...
    Posted to Forum by LarsBergen on 04-16-2009
  • What type of Powerlink cable is this? (Picture)

    Quick question but what type of powerlink cable is this with B&O PN 6250003? Asking since I was trying to find wiring info.
    Posted to Forum by kimhav on 01-26-2009
  • Beocenter 9500 with separate power amp creates "plopp" at "on" and "off"

    I connected my Beocenter 9500 via Powerlink (1 or 2 makes no difference) with a seperate power amp via a DIN-Cinch cable. The sound is great, however, when turning the Beocenter on and off, it creates a terrible "plopp" noise. It is so loud that I fear to destroy the speakters. So have to turn...
    Posted to Forum by lonelydog on 10-21-2008
  • It's been a LONG time... (Beovision 8 thread)

    Hi everyone, I have missed the posts and camaraderie here... I'm still thinking of a BV8, but I was curious how to integrate it into my setup, if and when I do get it. Currently I have a BS9000, connected to a BL2, and a pair of BL3s. I'd ideally like to ML the BS9K to the BV8, if I do this,...
    Posted to Forum by Sal on 07-31-2008
  • Configuring BeoSound 9000 and Beo Active?

    Hi , I have a Beosound 9000 with beolab 8000's connected directly with powerlink cables. i have recently connected a beolink active box and a pair of Pentas in a separate room. I cannot get the pentas to fire up whatever i try. i have set the link room to option 6 on the L.OPT. the IR module responds...
    Posted to Forum by andyfox33 on 12-30-2007
  • Power- and Masterlink cables

    Hi there, I need lots of cables for my new setup. Both Power- and Masterlink cables. And net cables aswell. So does anybody know if the Bosscom cables are just as good as original B&O cables? I reckon that Bosscom might be cheaper than B&O?? Greetings Ruivar
    Posted to Forum by Ruivar on 09-18-2007
  • Re: Concealed wiring wallplates

    Paddy, I think the stores have them made up to order. You could make your own for ML and PowerLink. Buy a blank HPM or Clipsal plate and start drilling and filing. I wouldn't recommend placing 240v outlet on the same plate though, I'd aim to keep a 10 cm separation, and have the two plates (twin...
    Posted to Forum by Goldfrog88 on 06-30-2007
Page 2 of 2 (19 items) < Previous 1 2