Untitled Page

ARCHIVED FORUM -- April 2007 to March 2012
READ ONLY FORUM

This is the first Archived Forum which was active between 17th April 2007 and 1st March February 2012

 

Search

Page 7 of 16 (159 items) « First ... < Previous 5 6 7 8 9 Next > ... Last »
  • Re: LX/MX motor stand plug wiring

    In case anyone else ever needs to know how to wire an MX motor stand I will document it here: - Pin 1 - Yellow Pin 3 - White Pins 2 & 4 - Green & Brown (pins 2 & 4 are connected on the board) The motor unit has far more to it than I expected; 2 pcbs with some kind of Intel chip, a crystal, about 6 small capacitors and lots of smd. Richard
    Posted to The Workbench (Forum) by richtoy on 12-08-2009
  • Re: LX/MX motor stand plug wiring

    Thanks Jaff I have a similar diagram in my LX5500 manual but it does not state which wire is which. As a last resort I can strip the stand down so see which colour wire goes to the motor and which to the position transducer but I was hoping to avoid that if possible... Richard
    Posted to The Workbench (Forum) by richtoy on 12-06-2009
  • LX/MX motor stand plug wiring

    I have aquired a motor stand for my old LX but it has lost its plug. There are 4 wires; green, white, yellow and brown. Does anyone know to which pin each wire goes? Better still, if anyone has one could you possibly open the plug and post a picture? Thanks, Richard
    Posted to The Workbench (Forum) by richtoy on 12-06-2009
  • Re: Prizedraw countdown bug

    What about more expensive prizes and have a draw every week
    Posted to General Forum (Forum) by richtoy on 12-02-2009
  • Prizedraw countdown bug

    There appears to be a slight problem with the time to next prize darw calculation... It says the next draw is in 362 days 6 hours 36 minutes Richard
    Posted to General Forum (Forum) by richtoy on 12-02-2009
  • Re: Beomaster 6000

    Beware of snake oil... I have recapped many B&O and as long as you use low ESR 105 degree C capacitors you will be fine. For coupling capacitors of value 4.7uF and below you can also opt for WIMA non electrolytic capacitors. I tried these when I replaced the tantalums in a BM3400 quad (user mahnem recommended) and I think you can hear the difference;
    Posted to Vintage Products (Forum) by richtoy on 11-28-2009
  • Re: MCL 2p gone bad

    If the black rectangle to which you refer is 2.5" x 1.75" and the stuff leaking out is white then it is normal. The device is a power amplifier integrated circuit and the white stuff is heatsink compound. Unfortunately there is no service manual for the MCL2P on the site so further help is a little tricky...
    Posted to The Workbench (Forum) by richtoy on 11-24-2009
  • Re: Christmas came early for me this year

    You are absolutely right Mika What you don't see from the pictures is the 10m of cable that connect the two units together and you would not want line level signals travelling 20m...
    Posted to Vintage Products (Forum) by richtoy on 11-01-2009
  • Re: Christmas came early for me this year

    As promised, here are the pictures of the internals and scans of the circuit diagram. There is black tube shaped device in the second picture (Phillips RPY13). You can read about it here http://www.tubecollector.org/rpy13.htm Enjoy
    Posted to Vintage Products (Forum) by richtoy on 11-01-2009
  • Re: Christmas came early for me this year

    Thanks Rudy As soon as I saw it I emailed and telephoned with the asking price. It was only 50km away too... I spent another 50 euro yesterday on din plugs and cable and that is just to connect the 5 amplifiers and the 5 line-outs Once today's Grand Prix is over I think I will have a bit of soldering to do Richard
    Posted to Vintage Products (Forum) by richtoy on 11-01-2009
Page 7 of 16 (159 items) « First ... < Previous 5 6 7 8 9 Next > ... Last »