https://archivedforum.beoworld.org:443/forums/29.aspxHave a specific BeoGram Record Deck related question? Ask here.enCommunityServer 2008 SP2 (Build: 31104.93)https://archivedforum.beoworld.org:443/forums/thread/70185.aspxSat, 08 Dec 2007 07:17:06 GMT41a2a90c-3a1e-4bd3-b144-3883695a7f38:70185junkonhill0https://archivedforum.beoworld.org:443/forums/thread/70185.aspxhttps://archivedforum.beoworld.org:443/forums/commentrss.aspx?SectionID=29&PostID=70185<p>Yes. I checked it out carefully.&nbsp; Do you think&nbsp;you may have that part? I had just about given up hope. Please let me know.</p><p>Thanks, Jim&nbsp;</p><div style="clear:both;"></div>https://archivedforum.beoworld.org:443/forums/thread/70151.aspxSat, 08 Dec 2007 03:14:40 GMT41a2a90c-3a1e-4bd3-b144-3883695a7f38:70151Dillen0https://archivedforum.beoworld.org:443/forums/thread/70151.aspxhttps://archivedforum.beoworld.org:443/forums/commentrss.aspx?SectionID=29&PostID=70151<p>I have a little stock of good used parts but did you look inside the deck ?&nbsp;</p><p>Martin</p><div style="clear:both;"></div>https://archivedforum.beoworld.org:443/forums/thread/70122.aspxFri, 07 Dec 2007 19:00:47 GMT41a2a90c-3a1e-4bd3-b144-3883695a7f38:70122junkonhill0https://archivedforum.beoworld.org:443/forums/thread/70122.aspxhttps://archivedforum.beoworld.org:443/forums/commentrss.aspx?SectionID=29&PostID=70122Thank&nbsp;you very much for this info. Now the next question; Do you have any idea where I might find one?&nbsp; Thanks again,&nbsp; Jim<div style="clear:both;"></div>https://archivedforum.beoworld.org:443/forums/thread/70096.aspxFri, 07 Dec 2007 17:10:16 GMT41a2a90c-3a1e-4bd3-b144-3883695a7f38:70096Dillen0https://archivedforum.beoworld.org:443/forums/thread/70096.aspxhttps://archivedforum.beoworld.org:443/forums/commentrss.aspx?SectionID=29&PostID=70096<p>Welcome to Beoworld !&nbsp;</p><p>Yes, there should be a&nbsp;brass pulley on the motor shaft,&nbsp;apprx 10mm&nbsp;in diameter. It&#39;s a press-fit but will also have been glued.</p><p>Martin</p><div style="clear:both;"></div>https://archivedforum.beoworld.org:443/forums/thread/70059.aspxFri, 07 Dec 2007 15:07:07 GMT41a2a90c-3a1e-4bd3-b144-3883695a7f38:70059junkonhill0https://archivedforum.beoworld.org:443/forums/thread/70059.aspxhttps://archivedforum.beoworld.org:443/forums/commentrss.aspx?SectionID=29&PostID=70059My model 1700 B&amp;O T.T. is running slow.&nbsp; Here&#39;s my question; Should there be a belt guide on the motor spindle? The guides I have seen are brass and fairly thick. I think this would speed it to the proper rpm. The belt is currently running on the motor shaft itself. It seems a little loose to me. I haven&#39;t had this very long and bought a new belt, installed it, then checked the tt out. Any help on this would be appreciated.&nbsp; Thanks,&nbsp; Jim&nbsp;<div style="clear:both;"></div>