General Forum

Re: Beosystem 3 link problem

karcenty — Sat, 22 Mar 2008 06:21:04 GMT

That is a very expensive test ;-) I don't have any beosound system.

Karcenty

Re: Beosystem 3 link problem

Beoik — Sat, 22 Mar 2008 06:02:03 GMT

Have you tried to connect a beomaster (sound) to the masterlink plug in the linkroom?

this way you can test the masterlink connection. choose cd in the livingroom and see if the cdplayer is reacting

Re: Beosystem 3 link problem

kawo — Fri, 21 Mar 2008 13:19:07 GMT

I am not sure with the MX, but when I got my used BV1 with ML socket and the Beolink did not work I realized that the BV1 just comes with the ML socket but not with the modul. AfterI got a modul from my dealer and pluged it in it worked....

Karsten

Re: Beosystem 3 link problem

karcenty — Fri, 21 Mar 2008 13:16:42 GMT

Yes, and I have tried different freq. as well.

Karcenty

Re: Beosystem 3 link problem

Marder — Fri, 21 Mar 2008 12:55:38 GMT

Have you checked the LINK frequens on the BeoSystem 3 should be 599?

/Mads

Re: Beosystem 3 link problem

karcenty — Fri, 21 Mar 2008 12:38:35 GMT

Have also been tried with no luck.

Karcenty

Re: Beosystem 3 link problem

Beoik — Fri, 21 Mar 2008 11:40:28 GMT

I had a similar problem with an beolink 1611. Solution was to first plug the mx to the mains , wait a few secondsand than the beolink to the mains.

Re: Beosystem 3 link problem

karcenty — Fri, 21 Mar 2008 11:34:12 GMT

It makes no difference. There is no connection between mx4000 and the BS3. If I hold down the red stop button in one room for 3-5 sec. it is only the TV in that room that turns off, normally both TV would turn off.

It also makes no difference if I disconnect the Beolink Video, only reaction is "snow" on the screen.

Well I think that I will get a B&o technician to take a look at the problem.

Thanks very much for your good suggestions.

Karcenty

Re: Beosystem 3 link problem

frankmj — Fri, 21 Mar 2008 11:08:06 GMT

....mr anders(son):
frankmj:

What if you bypass the RF amplifier and press v.tape in the link room. Does the Video start?
/Frank

You must use RF amp. It´s only picture that goes there. All commands goes through ML

I know, it was just to test the ML-connection, if that works, he has to look at the amp. and the connections to RF.

/Frank

Re: Beosystem 3 link problem

mr_anders_son — Fri, 21 Mar 2008 11:02:10 GMT

frankmj:
What if you bypass the RF amplifier and press v.tape in the link room. Does the Video start?
/Frank

You must use RF amp. It´s only picture that goes there. All commands goes through ML

Re: Beosystem 3 link problem

frankmj — Fri, 21 Mar 2008 10:50:18 GMT

What if you bypass the RF amplifier and press v.tape in the link room. Does the Video start?

/Frank

Re: Beosystem 3 link problem

karcenty — Fri, 21 Mar 2008 09:12:20 GMT

I checked and double checked every cable, I even made a new ML cable, but it make no difference. Maybe it is a hardware error.

Karcenty.

Re: Beosystem 3 link problem

frankmj — Fri, 21 Mar 2008 08:08:35 GMT

Then I would check the ML-cable and the junction box if you got any.

/Frank

Re: Beosystem 3 link problem

mr_anders_son — Fri, 21 Mar 2008 08:06:10 GMT

check the connection with the amplifier

in/out etc

AND you must have BS3 in opt 2

Re: Beosystem 3 link problem

karcenty — Fri, 21 Mar 2008 07:59:41 GMT

Thank you, but they allready are.

Karcebty