General Forum

Re: LC2 - reset sequence?

Hagen2000 — Mon, 12 Jan 2009 14:27:13 GMT

Interesting point. I will check this next time...

Re: LC2 - reset sequence?

Gunfai — Sun, 11 Jan 2009 14:55:31 GMT

2): I had the same problem but it worked when i pressed Store again after the command. Perhaps there are different versions?

Re: LC2 - reset sequence?

Hagen2000 — Thu, 06 Mar 2008 02:08:04 GMT

@kokomo

A standard dimmer can not be controlled by the B&O remote control...

@Ignace

Yes, I know this too!

---

I was just looking for a global reset sequence, that can not be found in the standard operating manual. Something that might be found in a service manual or something like this.

Re: LC2 - reset sequence?

Ignace — Wed, 05 Mar 2008 10:50:47 GMT

Hagen2000:
Ignace:
LIGHT, GOTO, 0, STORE, 4
restore factory default setting for ordinary light-bulbs

Hi Ignace,
this applies only to the choice of "energy saving lamps or ordinary light-bulbs" but not for other settings.

Hi, yes.

What about the other "return to factory default" setting :

(while touching the dome)

LIGHT, GOTO, 0, STORE, 2 ?

Re: LC2 - reset sequence?

Kokomo — Wed, 05 Mar 2008 10:39:47 GMT

On your first point, If you just want the light to operate as an on/off/dimmer switch having no number assigned to it, then it seems an LC2 is an expensive option for this when a more simple and cheaper standard dimmer switch would suffice. Unless you have all the available numbers in use for various light pictures using different other LC2s you may have, why not just assign it to any number, say # 9, then just avoid pressing this on your RC and use the LC2 directly?

On your second point, you probably know this (but I didn't at first!) ensure you are touching the LC2 whilst programming the on/off option.

Re: LC2 - reset sequence?

Hagen2000 — Wed, 05 Mar 2008 08:42:45 GMT

Ignace:
LIGHT, GOTO, 0, STORE, 4
restore factory default setting for ordinary light-bulbs

Hi Ignace,

this applies only to the choice of "energy saving lamps or ordinary light-bulbs" but not for other settings.

Re: LC2 - reset sequence?

Hagen2000 — Wed, 05 Mar 2008 08:41:44 GMT

kokomo:
Hagen2000:
Hi,
I would like to know if there is a reset sequence for an LC2 dimmer, i.e. to reset it to factory defaults, clear individual numbering etc.
Is any information available, what the actual firmware version of the LC2 should be and what corrections have been done in the firmware?
Thanks!

Don't quite follow what you want to do and why. Do you want the LC2 not to respond to any number whatsoever and just respond to Light Light without having any number allocated? Why wouldn't you want to allocate it a number or change it from its present one?

1. Yes, I want to be sure that there is no individual number assigend to the LC2 (setting it to number 0 seems to work but the manual doesn´t mention this). May be there are other parameters that need to be reset. That is why I asked for a reset sequence. B.t.w. LIGHT LIGHT always addresses all LC2, their individual numbering is irrelevant in this case.

2. A second reason is that one of my LC2 seems not to react to the sequence LIGHT GOTO 0 STORE 1 - programming the on/off function to "off". After disconnecting and reconnecting the mains, the lamp is lit up even though it shouldn´t.

3. The LC2 seems to be able to "remember" the brightness level that shall be activated when power goes off and on again. I assume that there exist further programming steps not explained in the manual to control this function.

4. In the english manual I found also LINK LIGHT pictures that are not explained in the german manual.

Re: LC2 - reset sequence?

Ignace — Wed, 05 Mar 2008 06:44:37 GMT

LIGHT, GOTO, 0, STORE, 4

restore factory default setting for ordinary light-bulbs

Re: LC2 - reset sequence?

Kokomo — Wed, 05 Mar 2008 06:19:54 GMT

Hagen2000:
Hi,
I would like to know if there is a reset sequence for an LC2 dimmer, i.e. to reset it to factory defaults, clear individual numbering etc.
Is any information available, what the actual firmware version of the LC2 should be and what corrections have been done in the firmware?
Thanks!

Don't quite follow what you want to do and why. Do you want the LC2 not to respond to any number whatsoever and just respond to Light Light without having any number allocated? Why wouldn't you want to allocate it a number or change it from its present one?

LC2 - reset sequence?

Hagen2000 — Wed, 05 Mar 2008 05:16:01 GMT

Hi,

I would like to know if there is a reset sequence for an LC2 dimmer, i.e. to reset it to factory defaults, clear individual numbering etc.

Is any information available, what the actual firmware version of the LC2 should be and what corrections have been done in the firmware?

Thanks!