General Forum

Re: tried aux socket on mx4002. Now ML doesn´t work

frankmj — Wed, 19 Dec 2007 17:30:17 GMT

hagan:

I tried to change cable, nothing.
One more queston: can i change mx 6000 with mx 5000 as master? Or even use mx 4002 as master?
regards

The MX4002 can't be a Video Master, unless you remove the ML module and change the software, then it will become a MX4000.

/Frank

Re: tried aux socket on mx4002. Now ML doesn´t work

hagan — Wed, 19 Dec 2007 15:28:39 GMT

I´ll answer myself. Changed mx 6000 for 5000. Worked fine from kitchen. Must be a faulty 6000 then

Re: tried aux socket on mx4002. Now ML doesn´t work

hagan — Wed, 19 Dec 2007 15:21:26 GMT

I tried to change cable, nothing.

One more queston: can i change mx 6000 with mx 5000 as master? Or even use mx 4002 as master?

regards

Re: tried aux socket on mx4002. Now ML doesn´t work

hagan — Wed, 19 Dec 2007 14:51:54 GMT

Ok!

So, even if it responds to commands from bm7000, for example AV CD it still can mess up link room commands?

I´ll have to check

Re: tried aux socket on mx4002. Now ML doesn´t work

cozza — Wed, 19 Dec 2007 14:45:36 GMT

Could be that the MX6000 has a bad solder connection on the Aux DIN socket data pin, or a broken wire in it's Audio Aux cable. That would cause the lack of response from the link rooms.

Re: tried aux socket on mx4002. Now ML doesn´t work

hagan — Wed, 19 Dec 2007 09:43:36 GMT

One more thing: Everything else works fine in all rooms. If I start MX6000 directly in localroom I can move sound to linkrooms but I cannot change channels etc from linkrooms. So I´m quite sure the MX 6000 doesn´t know it´s a master anymore???

regards

Re: tried aux socket on mx4002. Now ML doesn´t work

hagan — Wed, 19 Dec 2007 09:34:14 GMT

I have now tried almost everything, found all options and reprogrammed but mx 6000 doesn´t respond from linkrooms. I have tried disconnecting all other equipment and adding one by one but nothing.... Maybe the mx 6000 doesn´t know it´s a videomaster anymore?

regards

Re: tried aux socket on mx4002. Now ML doesn´t work

hagan — Wed, 19 Dec 2007 08:12:38 GMT

Yes! I depowered everything including converter. I`m acutally beginning to suspect my mx 6000. It doesn´t respond to any command from MCL or ML. I have MCL and speakerkit in kitchen and it doesn´t respond to commands from there either. When I connected the 4002 to aux I actually had two tv sets connected the same way at the same time to beomaster 7000. I used a y-cable. Can this have messed things up in mx 6000. At the same time I had a mx 5000 in another linkroom connected through a proper mcl video unit. Everything has worked fine until now.

Do I have to do some option programming again. If yes, update me on the options:

Room 1. Bm 7000 + MX6000. I like to have them in option 1 because of speaker config. Penta to mx and vox 5000 to Bm 7000

Kitchen. MCL speakerkit + cx 50

Bedroom1: Mx 5000 to videokit (mcl)

Bedroom2: MX 4002 to converter to y-cable and datalink in Room 1

regards

Re: tried aux socket on mx4002. Now ML doesn´t work

cozza — Wed, 19 Dec 2007 06:29:27 GMT

Have you depowered the Beolink converter? It will automatically configure when powered up. There is no option in the MX service menu to select between AAL and ML.

Re: tried aux socket on mx4002. Now ML doesn´t work

Zwets — Wed, 19 Dec 2007 06:20:08 GMT

Perhaps there is a setting in the service menu to set the MX to ML or AUX?

Re: tried aux socket on mx4002. Now ML doesn´t work

hagan — Tue, 18 Dec 2007 23:46:02 GMT

Hi!

Doesn´t work unfortunately. There was a small plastic cover over the aux socket. Is it important. I have lost it. But it was just a small piece of plastic

Re: tried aux socket on mx4002. Now ML doesn´t work

joeyboygolf — Tue, 18 Dec 2007 16:06:44 GMT

Disconnect everything from the mains. Re-connect as you want it. Then connect to power again.

tried aux socket on mx4002. Now ML doesn´t work

hagan — Tue, 18 Dec 2007 15:36:37 GMT

Hi!

I tried the aux socket on my mx 4002 connected to a Bm7000 and mx6000 through a converter. I remowed the converter and connected the aux cable directly. After this my V8000 doesn´t respond to any commands from the bedroom when I connected the converter again. The tv works in the same way as when connected to aux. How can I reset this back to normal??

Regards