General Forum

Re: BEOLINK 7000 STOPPED RESPONDING, ANY HELP & INPUT APPRICIATED

Ulf — Wed, 07 Nov 2007 12:28:13 GMT

You need only 2, but it's ok .

Look at these....

Ulf

Re: BEOLINK 7000 STOPPED RESPONDING, ANY HELP & INPUT APPRICIATED

larryk — Mon, 05 Nov 2007 03:51:26 GMT

Thank you Ulf. I'll see if I can find a tech to do the repair. Larry.

Will these work ?

http://cgi.ebay.com/Radial-Tantalum-Capacitors-22uF-16V-10-Clr-Code-25_W0QQitemZ170165471288QQihZ007QQcategoryZ40114QQssPageNameZWDVWQQrdZ1QQcmdZViewItem

Re: BEOLINK 7000 STOPPED RESPONDING, ANY HELP & INPUT APPRICIATED

Ulf — Thu, 01 Nov 2007 10:23:47 GMT

Sorry not,

the Capacitors can be 22uF 16 V SMD or Tantal.

My and any other BL7000 works fine after replacing the old Capacitors :)

Ulf

Re: BEOLINK 7000 STOPPED RESPONDING, ANY HELP & INPUT APPRICIATED

larryk — Mon, 29 Oct 2007 12:24:22 GMT

Thanks Peter, Hopefully someone has the values. I talked with Atlantic Systems here in the States and they did not here of this fix. They think it's a faulty module, and those are no longer availible. Larry.

Re: BEOLINK 7000 STOPPED RESPONDING, ANY HELP & INPUT APPRICIATED

Peter — Sun, 28 Oct 2007 14:55:03 GMT

Actually it turned out that it was the Beomaster at fault and not the Beolink. Unfortunately the values of the capacitors are not listed in the very sketchy service manual so it will be a case of seeing what you have when you open it up unless one of our experts can advise.

Re: BEOLINK 7000 STOPPED RESPONDING, ANY HELP & INPUT APPRICIATED

larryk — Sun, 28 Oct 2007 13:40:30 GMT

My Beolink 7000 has the same problem that AAVALENTA is experiencing. If replacing the capacitors would solve the problem this would be great. Anyone know what value capacitors to use ? Thanks to all, Larry.

Re: BEOLINK 7000 STOPPED RESPONDING, ANY HELP & INPUT APPRICIATED

Peter — Sun, 21 Oct 2007 13:10:36 GMT

The advice above is good - but I would suggest that if you are not experienced in electronics, that you get someone to do this for you. It requires very fine soldering and a mistake could be quite expensive!

Re: BEOLINK 7000 STOPPED RESPONDING, ANY HELP & INPUT APPRICIATED

AAVALENTA — Sun, 21 Oct 2007 12:59:15 GMT

HI MARTIN

THANK YOU SO MUCH FOR YOUR ADVISE. WHAT TYPE OF SMD CAPACITORS SHOULD I BUY AS A REPLACEMENT? AND ALSO SHOULD I REPLACE ALL 5 OR JUST THE 2 VERTICAL ON THE LEFT FROM THE IR TRANSMITTERS?? WOULD YOU HAVE ANY NUMBER AND (OR) SPECS WHEN I GO TO THE ELECTRONICS STORE TO TELL THEM WHAT IS THAT I NEED?

AGAIN MANY THANKS FOR YOUR ADVISE?

Re: BEOLINK 7000 STOPPED RESPONDING, ANY HELP & INPUT APPRICIATED

AAVALENTA — Sun, 21 Oct 2007 12:56:24 GMT

HI ULF,

THANK YOU SO MUCH FOR YOUR ADVISE. WHAT TYPE OF CAPACITORS SHOULD I BUY AS A REPLACEMENT? AND ALSO SHOULD I REPLACE ALL 5 OR JUST THE 2 AT THE TOP NEXT TO THE IR TRANSMITTERS??

AGAIN MANY THANKS FOR YOUR ADVISE?

Re: BEOLINK 7000 STOPPED RESPONDING, ANY HELP & INPUT APPRICIATED

AAVALENTA — Sun, 21 Oct 2007 12:52:41 GMT

HI PETER,

NO I DO NOT HAVE A LINK SYSTEM. SO THERE WOULD BE NO OTHER WAY FOR ME TO TROUBLESHOOT.

THANK YOU SO VERY MUCH FOR YOUR KIND HELP!! SINCERELY ALEX

Re: BEOLINK 7000 STOPPED RESPONDING, ANY HELP & INPUT APPRICIATED

Die_Bogener — Sun, 21 Oct 2007 08:41:53 GMT

They are under the metal shield, two SMD capacitors... and some more. There are 5 of them which should be replaced. The yellow ones ;)

http://img521.imageshack.us/img521/9089/beolink7000elkosld8.jpg

And clean the board with water and paint thinner, the acid of the defect capacitors makes lots of trouble.

For replacement you can use miniature elkos instead, much easier for soldering.

Martin

Re: BEOLINK 7000 STOPPED RESPONDING, ANY HELP & INPUT APPRICIATED

Ulf — Sun, 21 Oct 2007 05:12:22 GMT

There are two little capacitors at the receiving point of the BL7000.

Replaces the two capacitors, then it goes again

Ulf

Re: BEOLINK 7000 STOPPED RESPONDING, ANY HELP & INPUT APPRICIATED

Peter — Sun, 21 Oct 2007 02:30:51 GMT

Well it shows that the IR emitter on the 7000 works and that the receiver on the 5500 works. The fault seems to be either with the receiver on the 7000 or the emitter on the 5500. Do you have a link system? Does the 7000 work in a link room? If it does, the 5500 has a fault. If not, the 7000 receivers need attention. Tricky job! I believe one of our members, ridax, has experience in fixing these. There used to be a dedicated unit at Struer who made and fixed these but I think it no longer is in operation.

BEOLINK 7000 STOPPED RESPONDING, ANY HELP & INPUT APPRICIATED

AAVALENTA — Sat, 20 Oct 2007 17:14:54 GMT

I HAVE HAS BEOLINK 7000 FOR MANY MANY YEARS. MY BEOMASTER'S 5500 MAIN MOTHERBOARD HAS BEEN UPGRADED SO IT WOULD COMMUNICATE WITH THE BEOLINK 7000. IT HAS WORKED FLAWLESSLY FOR SEVERAL YEARS, BUT SUDDENLY IT HAS STOPPED COMMUNICATING. THE BEOLINK WORKS ONE WAY, HOWEVER, I GET "NO CONTACT" CONSTANTLY, NO MATTER HOW MANY TIMES I TRY TO DO THE INITIAL SET-UP ETC. STILL CONTACT. IF ANYONE KNOWS ANYTHING ABOUT THIS ISSUE, PLEASE ADVISE.

THANK YOU VERY MUCH!!

SINCERELY ALEX

LOS ANGELES, USA

ALEXVALENTA@ROADRUNNNER.COM