General Forum

Re: Beolink MX5000 to Beocenter 9000?

beoguy — Tue, 09 Oct 2007 10:50:07 GMT

Thanks Iggy!

I was not pressing sound 1 store! I also looked on your website and it says if you push shift+radio it opens the AUX connection. It works! However, it does not work when I press link+shift+radio, OR av+shift+radio.

Is this because I don't see the sticker marked Beolink? Is that part still available, and is it something I can intall?

Thanks Again!

Guy

Re: Beolink MX5000 to Beocenter 9000?

Ignace — Tue, 09 Oct 2007 08:47:51 GMT

Hi Guy,

I've run your components through the Config software and it came up with Option 1.5 for both MX and BeoCenter.

************************* VIDEO SYSTEM SETUP **************************

Beovision MX 5000

Connection Video

Connect the aerial to the aerial input of the TV-set.

Selecting option on the TV-set

Option: OPTION 1.5 (Factory setting)

Press:   STANDBY PICTURE 1 STORE
                  PICTURE 5 STORE

If option programming is made using Beolink 1000 MK3/MK4 or MK5 press
LINK before the sequence PICTURE x STORE

************************* AUDIO SYSTEM SETUP **************************

Beocenter 9000
Beovox passive

Connection Audio

Connect the Beovox to the SPEAKERS 1 socket on the audio
master using a loudspeaker cable.

Connect the aerial to the aerial input of the audio master.

Selecting option on the audio master

Option: OPTION 1.5

Press: STAND-BY   SOUND 1 STORE
                   SOUND 5 STORE

If option programming is made using Beolink 1000 MK3/MK4 or MK5 press
LINK before the sequence SOUND x STORE

********************* AUDIO/VIDEO/LINK SYSTEM SETUP *******************

To obtain A/V intergration between these products the audio master
must be equipped with a Beolink software, part no. 8341052.
If the audio master is equipped with a Beolink software, it is
indicated by a sticker marked BEOLINK on the rear panel.

Beolink MX5000 to Beocenter 9000?

beoguy — Mon, 08 Oct 2007 19:01:18 GMT

I'm sure I'm doing something wrong and someone here will be able to set me straight! I have just added a datalink cord from my North American MX5000 to my Beocenter 9000. I have placed one end to the Aux/Line of the MX, and the other to the Aux of the Beocenter.

O.K....I programmed the tv for "picture 1 store" because the two components are close.

From the MX5000, through my beolink 1000, I press the AV+whatever I want to call up from the Beocenter 9000. All is fine!

Now with everything off (stand by). When I aim the Beolink 1000 to the Beocenter 9000 and press AV+TV...nothing. So I try Link+TV. Now the Tv's standby light turns off (with a click)...but no sound from Beocenter or tv. If I press the standby on the Beolink 1000 and continue aiming it at the Beocenter 9000, the TV does switch to standby.

I read the Beocenter 9000 manual (I have a European manual). It tells me to press AUX+1 for TV, or AUX+5 for VCR. I key this in directly to the Beocenter and voila, it works. Now...I would like to be able to do this from the remote. I cannot find AUX on the remote. I'm sure that it must be an early version. So...how can I do this with the remote?

Any ideas?

Guy