General Forum

Re: Motorstand

Razlaw — Sun, 11 Dec 2011 19:15:23 GMT

Russ:
Hello all, silly but please try and report. Go back through the menu set up and store all the settings, then pull main power for 45 seconds, plug back in and try.

Tried what you suggested with my 7-55. It did not work.

Re: Motorstand

Raeuber — Sun, 11 Dec 2011 19:03:18 GMT

Hi moxxey,

on my new BV 7-40 3D the stand moves into a programmed audio position. Only if the TV is off and I press RADIO or CD it doesn´t move. But probably this is intended from B&O.

I assume the latest software is on the new BV 7-40 3D and maybe it´s also available for your BV 7.

/Räuber

Re: Motorstand

Russ — Sun, 11 Dec 2011 18:59:52 GMT

Hello all, silly but please try and report. Go back through the menu set up and store all the settings, then pull main power for 45 seconds, plug back in and try.

Re: Motorstand

moxxey — Sun, 11 Dec 2011 17:47:19 GMT

Raeuber:

Hi Razlaw,

ok, but thank you very much for your support. Probably your BV´s need a software update to make it work.

My BV7-40 has the lastest software and the stand never moves in audio-only mode. I rarely listen to the TV in audio-only mode, so it's not a problem for me. But it's definitely a mode that never works.

Maybe no-one reported it to B&O? :)

Re: Motorstand

Razlaw — Sun, 11 Dec 2011 17:06:29 GMT

Yes, hope so. However, my BV 10-40 was updated last week with the most recent software.

Re: Motorstand

Raeuber — Sun, 11 Dec 2011 16:55:56 GMT

Hi Razlaw,

ok, but thank you very much for your support. Probably your BV´s need a software update to make it work.

I want to ensure that it works properly with my new BV 7-40 3D.

So probably someone else can answer the question in my first post...

/Räuber

Re: Motorstand

Razlaw — Sun, 11 Dec 2011 16:50:46 GMT

No, does nothing. But it is ot an issue for me. I want the TV in standby position when listening to Audio and ut does that fine. Does not matter to me if a dedicated audio position does not work.

Re: Motorstand

Raeuber — Sun, 11 Dec 2011 15:54:14 GMT

Very crazy!

Please check the following with BV 7 and BV 10:

Press DTV and wait until picture appears and the motorstand are in video position. Then select P.MUTE or AV DTV. The motorstand should turn to the programmed audio position.

Re: Motorstand

Razlaw — Sun, 11 Dec 2011 15:41:37 GMT

I just tried it with my BV 10-40 also. Programmed an audio stand position. Scrolling through the three positions in the steup menu it would turn to each of the three. However, just as with the 7-55, turning an Audio source on does nothing.

Re: Motorstand

Raeuber — Sun, 11 Dec 2011 14:54:28 GMT

So if you have connected an audio source via masterlink to your BV 7-55 and you select Radio or CD, the motorstand should turn to the programmed audio position. My BV 7-40 does so, but only if the TV is switched on before to video.

Re: Motorstand

Razlaw — Sun, 11 Dec 2011 14:33:45 GMT

yes

Re: Motorstand

Raeuber — Sun, 11 Dec 2011 13:51:22 GMT

Razlaw:

I have never thought about that so I just tried it with my BV7-55. My stand never moves to the Audio position.

Did you program a different motorstand position for audio in the setup??

Re: Motorstand

Razlaw — Sun, 11 Dec 2011 13:45:01 GMT

I have never thought about that so I just tried it with my BV7-55. My stand never moves to the Audio position.

Motorstand

Raeuber — Sun, 11 Dec 2011 12:42:42 GMT

Hi all,

on my BV 7-40 it is possible to program different positions for the motorstand (video, audio, standby). Normally the positions for audio and standby will be the same.

I have programmed different motorstand position for audio and standby (for test purposes). When I choose an audio source from standby (Radio or CD), the BV 7-40 doesn´t turn to the programmed audio position, it remains in standby position. Only if the BV 7-40 is already in (video) use, the motorstand turns to the programed audio position.

Is this issue correct or a software bug?

Thanks for testing!

Regards

Räuber