General Forum

Re: New To B&O

Blackrix — Sun, 19 Jun 2011 07:31:59 GMT

BeoLab 2500 does not have 2 Powerlink-sockets. So you need a Powerlink Y-splitter to get this to work. Or you should go from BeoCenter 2300 to a BeoLab 6000 and connect the BeoLab 2500 to the second PL-socket of the BeoLab 6000, but I think you might need a lot more PL-cable for that option!

Re: New To B&O

plumber77 — Sun, 19 Jun 2011 06:59:12 GMT

thanks alot. That is very helpful indeed

Re: New To B&O

stefan — Sun, 19 Jun 2011 06:08:11 GMT

For your setup with BL2000 you need a BL converter - 1611 - an AUDIO AUX LINK cable (7pin DIN plugs), a Masterlink cable and ofcourse a BL2000.

Yes, you can daisychain BL2500 and BL6000 via Powerlink connected to your BC2300. You won`t have independant control between these two speakers. But you will have independant control between this (main) setup and BL2000 (link) setup.

You can find interesting info about Beo-setups on the Beotech site. Masterlink setups with BL converter and BL2000: http://www.beoworld.org/beotech/options3.htm

Hope this helps.

Stefan

Re: New To B&O

plumber77 — Sat, 18 Jun 2011 12:32:13 GMT

Thanks.

So I just need a beolink converter? 1611 I was told

I presume I could daisy chain the 6000's with the beolab 2500's which are already on the BC2300.

Re: New To B&O

stefan — Sat, 18 Jun 2011 06:28:44 GMT

Yes. You can connect BL6000s to Powerlink out of your BC2300, a Beolink converter to the AUX port and your BL2000 in your linkroom to the Masterlink socket of the BL converter. Independant control in both rooms is possible, but - of course - you can just listen to one CD track or one radio station at the same time via the link system....

Stefan

Re: New To B&O

plumber77 — Fri, 17 Jun 2011 15:58:39 GMT

stefan:
I mean simple to install and simple to use. You just need one Beolink converter (1611) for your Beosound and you can connect BL2000, BL3500, Beolink active, passive, all newer Beovisions in linkrooms with Beo4/6 control from every linkstation and independant volume control via one single Masterlink cable. This is not possible if you just add speakers - but it will work too.

Is it possible to have the beosound 2300 with beolab speakers on one rooms with a pair of 6000's connected directly to them then using a beolink converter add a BL 2000 in say a bedroom so it has independant control.

I have looked around and can get the converter for about £60. (I think!)

Re: New To B&O

Søren Mexico — Fri, 17 Jun 2011 14:00:27 GMT

1) Powerlink mark 1 cable is only useful for non-digital Beolab speakers without displays.

2) Powerlink mark 2 can be used for ANY Beolab speaker with 8pin sockets.

3) Powerlink mark 3 can be used for any Beolab speaker WITHOUT displays EXCEPT Beolab 5.

Re: New To B&O

plumber77 — Fri, 17 Jun 2011 10:57:09 GMT

thanks for your help.

how do I find out which powerlink mark I have on the unit, ie mark i, ii or iii

Re: New To B&O

stefan — Fri, 17 Jun 2011 09:47:18 GMT

plumber77:

BTW: "Beo`s "All over the house control" is simple.

How do you mean simple??

I understand the beolab 2000's has control by selecting tape/radio/cd etc but is this possible with powerlink as my unit is older or would I need to get adaptors to masterlink?

I mean simple to install and simple to use. You just need one Beolink converter (1611) for your Beosound and you can connect BL2000, BL3500, Beolink active, passive, all newer Beovisions in linkrooms with Beo4/6 control from every linkstation and independant volume control via one single Masterlink cable. This is not possible if you just add speakers - but it will work too.

Stefan

Re: New To B&O

Søren Mexico — Fri, 17 Jun 2011 09:22:40 GMT

I forgot, as the BS 8 has no line out, get a cable that connect Ipod to AUX in, in the 2300, that way you can play your Ipod as well

Re: New To B&O

Søren Mexico — Fri, 17 Jun 2011 09:15:30 GMT

Run power link cables from speaker to speaker, each BL 2500 has 2 power link connections, BL 6000 as well, the 2300 also, so from 2300, 1 power link to BL 2500 R or L and from R to L, 1 powerlink from 2300 to BL 6000 R or L and from R to L or visa versa, on the last connected BL you will have an empty powerlink connection that one you can connect to more BL speakers.

One powerlink cable runs trigger power and lines for both R/L speakers, if the BL has 2 PL connections you can use one cable from 2300 to R BL from R to L BL, just remember to set the BLs selector to L or R

Re: New To B&O

plumber77 — Fri, 17 Jun 2011 08:59:56 GMT

BTW: "Beo`s "All over the house control" is simple.

How do you mean simple??

I understand the beolab 2000's has control by selecting tape/radio/cd etc but is this possible with powerlink as my unit is older or would I need to get adaptors to masterlink?

Re: New To B&O

stefan — Fri, 17 Jun 2011 08:52:11 GMT

plumber77:

Understood. I was using the beosound 8 seperate anyway with an Ipod connected.

Surely I must be able to just add a pair of 6000 speakers or similar to my existing beosound 2300.

Run 2 extra speakers as well as the beolab 2500's. I just want a simple system without the need for control all over the house. just play a cd on my system and it come out of extra speakers??

Yes, yoa can add BL6000s by using a Powerlink Y-splitter. The speakers will also get on-off commands via Powerlink. So, all speakers will be on or off.

BTW: "Beo`s "All over the house control" is simple.

Stefan

Re: New To B&O

plumber77 — Fri, 17 Jun 2011 08:40:42 GMT

Understood. I was using the beosound 8 seperate anyway with an Ipod connected.

Surely I must be able to just add a pair of 6000 speakers or similar to my existing beosound 2300.

Run 2 extra speakers as well as the beolab 2500's. I just want a simple system without the need for control all over the house. just play a cd on my system and it come out of extra speakers??

Re: New To B&O

Hiort — Fri, 17 Jun 2011 08:27:30 GMT

plumber77:

Ipod or computer linking is not an issue as I recently bought the Beosound 8.

It´s not possible to add Beosound 8 into a link system.

/Claes