General Forum

Re: STC not controlling Mac Mini but dut does control Sky+

Gerd — Sun, 12 Apr 2009 11:08:59 GMT

Not sure but I think your "compatible double emitter cable" will not work!

The IR-output socket has 3 pins where only pin 1 is common to both IR-transmitters.
By using an ordinary adaptor you will probably short-circuit one of the outputs.

The original adaptor has a chrome- and a gold-coloured socket for a primary (STB-SAT)
and a secondary (STB-V.AUX) set top box.

Check chapter "Connect a set-top box or decoder" of your reference manual.

Re: STC not controlling Mac Mini but dut does control Sky+

beolife — Sun, 12 Apr 2009 10:44:18 GMT

Keith,

The only other thing that I can think of is that the Sky+ is connected by S-Video & not by scart, therefore does not have Pin 8 connection,does this make a difference? The reason for this is that the Sky+ is connected to the Avant by scart because this is where the box is positioned & the S-Video connection feeds the Beosystem 2 in the playroom.

Gerd,

No I do not have the Y splitter, I have a compatible double emitter cable

Re: STC not controlling Mac Mini but dut does control Sky+

Gerd — Sun, 12 Apr 2009 04:39:02 GMT

Simon,

given that the Beosystem2 has only one IR-Output: how did you connect both IR-transmitters?
Did you use the original B&O Y-adaptor part number 7229212?

Re: STC not controlling Mac Mini but dut does control Sky+

Keith Saunders — Fri, 10 Apr 2009 02:46:48 GMT

Simon,

Let me be clear, in this new configuration you get exactly the same problem ? When V.AUX is pressed as a source the apple does NOT work ? is that correct ?

I have a feeling that I am missing a key piece of data from your "Problem Statement"

Re: STC not controlling Mac Mini but dut does control Sky+

beolife — Wed, 08 Apr 2009 14:59:24 GMT

Keith,

I have tried some different connection options, basically I have completely removed the input to the camcorder & reassigned the inputs so now it connected as follows.

V-tape-DVD

AV-STB (DTV) Sky+

Decoder-STB (V.AUX) Apple Remote

But it still does not work, I do not have anything physically connected to the camcorder inputs at all, I have also checked the voltage of the Wii that was connected when I first tried this config & they were 0.65Volts so below the figure you said, but as I said I also tried this with no connection at all & it still does not work. Very strange.

Hopefully you may be able to shed some more light on this issue.

Regards Simon

Re: STC not controlling Mac Mini but dut does control Sky+

beolife — Wed, 08 Apr 2009 12:40:45 GMT

Keith,

Would a AV expander get round the problem? or is it not suitable.

I will see if I can get a reading regarding the 0.7v issue etc.

Re: STC not controlling Mac Mini but dut does control Sky+

Keith Saunders — Wed, 08 Apr 2009 11:35:06 GMT

Simon,

The PCG is correct in the information it is giving you.

However, I can confirm that the Beosystem 2 camcorder input works in the same way as almost all other Beovisions in that if a source is plugged into the camcorder input it automatically switches to that input and therefore disables the others.

Looking at the circuit it is clear that if an voltage appears on the input greater than 0.7 volt, then that will be enough to enable the camcorder input.

Re: STC not controlling Mac Mini but dut does control Sky+

beolife — Tue, 07 Apr 2009 05:52:06 GMT

Hi Keith,

I ran the set up through the PCG & this is what came out.

I am trying to keep the naming & assigning simple for the kids etc, it seems that there are some caveats regarding connections & what go's where, is there a list for the available inputs & whats remaining after you have assigned a device etc.

Hope this makes sense

BeoVision 4

Beolab 3

DVD 1

DVD 2 (VR 1)

Set-top Box Controller ( 2 STBs )

Connection Video

Connect the VR 1 to the V.TAPE socket of the TV-set using a

21/21-pin A/V cable.

Connect the DVD-player to the AV socket on the TV using a fully mounted 21/21-pin

A/V-cable.

If your television is equipped with a built-in Dolby Digital module,

connect the socket marked DIGITAL OUTPUT on DVD to the input 1 socket

on your television (cable 6270775).

Connect the TV terminal of the Set-top Box to the TV DECODER terminal

using a fully mounted 21/21-pin A/V cable.

Connect the enclosed IR-transmitter to the IR-OUTPUT terminal on the back of

BeoVision Avant and mount the IR-diode above the Set-top Box IR-receiver.

Connect the television socket on the Set-top box to the television's

Camcorder socket using a Set-top box Camcorder A/V cable. Order No. 6270792

Connect the supplied IR transmitter to the IR-OUTPUT socket on the back of

your BeoVision Avant, and position the IR diode above the IR receiver of the

Set-top box.

Connect the aerial to the aerial input of the VR 1.

Connect the aerial output of the VR 1 to the aerial input of the

TV-set using a coaxial cable.

Connect the Beolab to the POWER LINK socket (FRONT) on the BeoVision

using a Power Link cable.

Both Power Link sockets contain left and right channel information.

The signal may be looped through to the second Beolab using another

POWER LINK cable and a Power Link adapter, part No. 6270597.

Setting switches on the Beolab

Set the MODE switch to position L or R to determine whether the

loudspeaker should serve as a left or right loudspeaker.

The Position and Setup switch on the BeoLab should be adjusted according

to the guidelines in the enclosed guide.

Setting of switch on DVD

Set the switch on the back of the DVD 1 (Y/C - CVBS - RGB) to position RGB

To ensure that the DVD discs are played with the proper picture format,

please perfom this "once only" operation:

Press LIST on Beo4 until v.setup appears in the Beo4 display.

Press GO to display TUNE. Press 1 if the DVD1 is connected directly

to a BeoVision MX television.

Press 2 if the DVD1 is connected to a BeoVision MX via an AV2 Expander box,

or if DVD 1 is connected directly to any other Bang & Olufsen television.

Press GO to store the setup.

Default is mode 1.

Selecting option on the TV-set

Option: OPTION 2, with Beo4

Press: | Display:

-------------------------------------------

STANDBY + LIST at the same time | OPTION?

GO | V.OPT

2 | Observe confirmation

| from BeoVision

Programming the setup

Setup:

Procedure for the setting up of connected sources:

MENU / Setup / Connections

Fill in the menu as follows:

-----------------------------------------

V.Tape AV Decoder

V.Tape DVD STB (SAT)

-----------------------------------------

After filling in the menu, confirm the settings by pressing GO.

Now choose the desired Set-top Box on the list and confirm by pressing GO.

Set up connected sources as follows:

MENU / Setup / Connections / MENU

Complete the menu as follows:

--------------------------

Camcoder

STB (V.AUX)

Re: STC not controlling Mac Mini but dut does control Sky+

Keith Saunders — Tue, 07 Apr 2009 03:55:49 GMT

Simon,

I think your issue relates to the fact that you are using the Camcorder input.

I will need to check if it is true for the Beosystem 2, but on most B&O TV's if you use the Camcorder input it normally automatically sets that input as "to be used" if something is plugged into it and a signal is detected and at the same time it disables other inputs which appears to be your problem statement.

STC not controlling Mac Mini but dut does control Sky+

beolife — Tue, 07 Apr 2009 03:03:43 GMT

HI Guys,

posted in the BeoMac forum but thought I would post here as well because i think this is a STC issue & not a Mac problem.

Here is the original thread http://forum.beoworld.org/forums/t/25579.aspx

Here are the cut & pasted posts below.

Hi Guys,

Hope you can help, updated the STC in my Beosystem 2 to enable control of the Mac Mini, the Mac is set to (stb)V.Aux & set to apple remote but it does not work, it's not even flashing at all but the Sky+ can be controlled as normal.

Any Ideas.

Regards Simon

Managed to get it work but only if I removed the DTV STB from the connections list which is connected to the camcorder input, then it worked but if I put the DTV back in the SKY+ works but not the Apple.

Here is a list of the connections used

VMEM-DVD (sony)

AV-DVD2 Wii

DECODER-STB-VAUX (Mac Mini) set to apple remote

CAMCORDER-STB-DTV (SKY+) set to sky+

Really not sure why this is happening but very frustrating hopefully someone can shed some light on this issue.

Regards Simon