General Forum

Re: Bs3 & Penta display

The Stig - ver. 1.7 — Sun, 01 Jun 2008 09:47:22 GMT

sorry what i meant was power it off and then on again, to get the display data in sync.

Re: Bs3 & Penta display

a2bur — Fri, 30 May 2008 13:30:25 GMT

Hi Stig , thanks for your comments but can't turn off the Bs3 just for audio as all the speakers go from it for the 5.1 cinema and the Bs4500 is connected via a BeoLink converter . Did think about having a second Power Link circuit from the Bs4500 to the Penta's as there are two Power Links sockets in each Penta but would probably cost £300 + for the cables and might cause a back feed so think I have the best result I can get .

Richard

Re: Bs3 & Penta display

The Stig - ver. 1.7 — Thu, 29 May 2008 17:22:28 GMT

Your speaker has to be in Video and the BS3 has to be turn off for it to have an effect.

Re: Bs3 & Penta display

a2bur — Thu, 29 May 2008 01:57:10 GMT

Tried Video and Audio switch and altered the volume and other controls to see if that would kick them into life but no display . Tried one of the Penta's on my Bv7-40 and got audio display but no video , but I have a Bv6 linked to this 7 and if the 7 is in audio and then turn on the 6 the display went off . Looks to me as though the Bs3 will sometimes let data thru from equipment attached that outputs this information but cannot output data itself , at least my one doesn't . I have got the displays working with this special cable and all information is there ( Radio , track , aux ect ) except the correct volume .

Richard

Re: Bs3 & Penta display

The Stig - ver. 1.7 — Wed, 28 May 2008 16:37:28 GMT

The BS3 does support display data, have you set you pentas to video mode? instead of Audio...

Re: Bs3 & Penta display

a2bur — Tue, 27 May 2008 01:58:49 GMT

Installed last Friday and is software 4.17a . I've worked out a fix , I plugged in a full spec power link cable direct to one of the Penta's from the master and called for Cd thru the Bs3 ( all speakers connected to that ) and the displays work . All displays came on so looks like the power link data pins on the Bs3 are connected as it's the only way the other 5 Penta's can get the information . They are coming back today to alter a couple of things so I'm going to get them to make up a Power Link cable without the right and left channel , using full spec cable the speaker is getting sound information from two directions . The volume display is wrong as it shows what the Bs4500 is set at and not the Bs3 but can live with that .

Richard

Re: Bs3 & Penta display

The Stig - ver. 1.7 — Mon, 26 May 2008 17:37:26 GMT

Is your BS3 SW lower then 3.1?

Re: Bs3 & Penta display

a2bur — Sun, 25 May 2008 03:08:30 GMT

Hi Neil .

The drawing in the Beolink handbook shows pin7 shield/ground around the white/data wire 6 , the other ground/shield pin2 goes around the left and right signals . Looks to me that pin 6 and 7 are the one's . On the thin Powerlink cable pins 1 , 6 , 7 and 8 are not connected and am wondering if pin 1 is needed to trigger the display ?

Richard

Re: Bs3 & Penta display

nobby — Sun, 25 May 2008 02:39:29 GMT

Hi Richard,

Would seem to make sense ... is it worth setting up the system with the signal plus ground only to the penta and leaving the bs3 out to check this first?

Neil

Re: Bs3 & Penta display

a2bur — Sat, 24 May 2008 17:53:40 GMT

I've got the Beolink handbook , it shows the Powerlink wiring layout and pin 6 is datalink and pin 7 is it's shield/ground . I've connected these but no display and am a bit reluctant to try other combinations without knowing what I doing . The pin layout is as below .

Pin 1 = grey = power up/down

Pin 2 = shield = ground

Pin 3 = brown =signal left channel

Pin 4 = yellow = loudspeaker relay

Pin 5 = green = signal right channel

Pin 6 = white = datalink

Pin 7 = shield = ground

Pin 8 = pink = overload

I connected pin 6 & 7 on the Beomaster4500 to the same pins on one of the Penta's and commanded CD thru the Bs3 , speaker came on but no display . The data information must be there but the Bs3 doesn't pass it thru , my thinking is to bypass the BS3 with this data .

Richard

Re: Bs3 & Penta display

nobby — Sat, 24 May 2008 15:50:53 GMT

If I remember correctly, its a pair rather than a single line ... have you checked the schematics on the site?

Neil

Bs3 & Penta display

a2bur — Sat, 24 May 2008 05:57:13 GMT

Changed my BS4500 set-up to go thru a BeoSystem 3 via a datalink converter , have 6 Penta's and have now lost the displays as the BS3 doesn't support it and doesn't let the data thru . As the Powerlink sockets on the BS4500 master are not now used I am wondering if I could take a feed from pin 6 ( data ) and feed the Penta's to get the displays back when I use the audio ? Anyone know if this will work and are there any other pins needed ?

Richard