General Forum

Re: Motor stand for MX7000

nobby — Fri, 09 May 2008 12:07:26 GMT

Hi,

I usually retail these at £70. Can take yours off your hands, but to be honest, unless you are going to collect, it could start to get expensive with the postage.

You might be better off waiting for one to come up on ebay.

Cheers, Neil

Re: Motor stand for MX7000

sonicnozzle — Fri, 09 May 2008 06:56:13 GMT

Neil

Thanks for your reply, I would be interested in buying the whole unit if you cannot locate a replacement mounting plate.

Perhaps you would want my existing unit ?

Jack

Re: Motor stand for MX7000

nobby — Thu, 08 May 2008 03:20:51 GMT

Hi Jack,

Yes, one and the same :o)

I didnt find a plate yet only a complete motorised floor stand and it would be criminal to break it up. I have a few more sources to try.

Neil

Re: Motor stand for MX7000

sonicnozzle — Wed, 07 May 2008 14:42:56 GMT

Neil

I did not realise that you were "Nobby" perhaps I should read my mail with more care.

I assume that you do not have plate for sale?

If not the dimensions would allow me to esimate the Centre of gravity of the TV

Thanks again

Jack

Re: Motor stand for MX7000

nobby — Wed, 07 May 2008 08:27:30 GMT

No need to measure, this is the correct one for the 28inch MX

Neil

Re: Motor stand for MX7000

sonicnozzle — Wed, 07 May 2008 05:12:01 GMT

Thanks Jason

The photo is a great help, I have a MX7000 TV. Could you measure the overall width and length if the plate and the measurement from the turntable centre to the front edge of the plate.

The centre distances of the mounting holes would be very useful.

Thanks for all your help

Jack

Re: Motor stand for MX7000

Iconic-AV — Mon, 05 May 2008 17:12:02 GMT

no problem jack, the 4 raised holes on the edges fit the tv and the 6 small holes in the centre fit the motor,

hope this is what your after, or as craig said im sure Nobby should have one if you need one

regards jason

Re: Motor stand for MX7000

sonicnozzle — Mon, 05 May 2008 16:02:48 GMT

Jason

Thanks for your reply, the stand I have is off a LS5500 , a photo would allow me to see where the screw connections are located.

Thanks again

Jack

Re: Motor stand for MX7000

Iconic-AV — Mon, 05 May 2008 14:30:04 GMT

hi jack,

i have one in front of me, i can add a photo if it helps,

do you have the smaller mx4000 version to compare to? if not ill check it against one i have in the showroom tomorrow, the holes for the motor will be the same, let me know what measurments you need

jason

Re: Motor stand for MX7000

Craig — Mon, 05 May 2008 14:28:32 GMT

Jack, it might be worth dropping Nobby a PM knowing Neil, he may have the one you need in stock.

Craig

BTW, it was nice to see you again over the weekend

Re: Motor stand for MX7000

sonicnozzle — Mon, 05 May 2008 14:19:07 GMT

Thanks Craig

The motor stand does work with the MX7000 I just need details for the adaption plate.

Jack

Re: Motor stand for MX7000

nobby — Mon, 05 May 2008 13:44:11 GMT

Slight correction ... the MX8000 and MX4200 stands operate differently and there seems to be a compatability issue with some MX5000 stands.

Neil

Re: Motor stand for MX7000

Craig — Mon, 05 May 2008 12:56:09 GMT

Jack, I believe the motor unit is the same on all MX, LX, LS and L models. It is just the plate that is different. They all seem to have the same connection for the motor.

Craig

Motor stand for MX7000

sonicnozzle — Mon, 05 May 2008 12:42:36 GMT

Could anyone tell me if it is possible to use a motor stand MS 4106 on my MX 7000 TV or does some one have a stand for a MX7000 who could photograph the adaption plate so I could fabricate a new one ?

The MS 4106 looks identical to the MX 7000 unit but the fixings to the TV will be different.

Thanks

Jack