Untitled Page

ARCHIVED FORUM -- April 2007 to March 2012
READ ONLY FORUM

This is the first Archived Forum which was active between 17th April 2007 and 1st March February 2012

 

Search

Page 75 of 399 (3985 items) « First ... < Previous 73 74 75 76 77 Next > ... Last »
  • Re: Beogram 1700-funktioner

    Beogram 1700 regnes ofte som den bedste i sin serie men den har ikke en decideret stop funktion. Ved enden af pladen, kan den selv løfte og svinge armen ud men hvis du vil stoppe under afspilningen af en plade, trykker du pause, Beogram'en løfter så armen og stopper pladetallerkenen og du skubber selv armen ud. Med andre ord;
    Posted to BeoWorld Nordic (Forum) by Dillen on 02-27-2011
  • Re: Beogram 4002 - Arm only moving in one direction.

    Check the transistors in the H-bridge. Martin
    Posted to BeoGram (Forum) by Dillen on 02-24-2011
  • Re: Is this correct ???

    Did you shim up the coil/center piece ? And if you did, was it difficult to get it right ? The spider ? Did the woofer play for a long time with the bad surround ? Martin
    Posted to Vintage Products (Forum) by Dillen on 02-24-2011
  • Re: Beogram 7000 tone arm assembly not moving

    That is quite common. You can fit a short 3mm screw from below, through the hole in the carriage plate and put a tiny washer and a nut on the upper side. The string/spring can then hold on to the excess screw threading. Martin
    Posted to BeoGram (Forum) by Dillen on 02-24-2011
  • Re: Service på BeoCenter 4000 fra 1978...

    Hej, Det er altid utroligt svært at gætte på en reparations-pris på de ældre ting. Hvor meget skal skiftes og hvor meget skal laves. Skal den total renoveres hvor alle fejl klares, justeringer checkes, måske optiske fejl udbedres osv. eller skal den bare have lavet en reparation af en bestemt funktion. Hvorfor er
    Posted to BeoWorld Nordic (Forum) by Dillen on 02-24-2011
  • Re: Beogram 7000 tone arm assembly not moving

    You can put the rear cover back on again, no need to remove the dustcover. Put the Beogram on a table so that it's right edge is just 3-4 cm out over the table edge. Remove two screws from below along the right side. Push the Beogram back onto the table, lift off the platter and push the carriage as far to the left as it will go. The top part of
    Posted to BeoGram (Forum) by Dillen on 02-24-2011
  • Re: beomaster 8000

    Jeg kan sikkert sagtens lave den, jeg har lavet mange. Problemet er bare, at jeg har umådeligt travlt i øjeblikket så der kan gå et par måneder førend jeg eventuelt kan finde tiden til det. Andre steder ? Hmm... Jeg kender faktisk ingen, men jeg har nu heller aldrig haft brug for at kende nogle så det er nok
    Posted to BeoWorld Nordic (Forum) by Dillen on 02-23-2011
  • Re: beomaster 8000

    Velkommen til Beoworld ! Beomaster 8000 er en skøn receiver, jeg bruger selv sådan een hver dag og ville ikke være foruden. Varmeproblemet skyldes som regel en defekt tomgangs-regulering. Den må skiftes og efterjusteres. Når man så er i gang, skifter man også DC offset reguleringen og samtlige kondensatorer
    Posted to BeoWorld Nordic (Forum) by Dillen on 02-23-2011
  • Re: CD50 Terminal

    They are rare. This is the CD Terminal : Martin
    Posted to Vintage Products (Forum) by Dillen on 02-22-2011
  • Re: What Are You Working On Now ?

    Very nice work, Chris ! Martin
    Posted to The Workbench (Forum) by Dillen on 02-21-2011
Page 75 of 399 (3985 items) « First ... < Previous 73 74 75 76 77 Next > ... Last »