Untitled Page

ARCHIVED FORUM -- April 2007 to March 2012
READ ONLY FORUM

This is the first Archived Forum which was active between 17th April 2007 and 1st March February 2012

 

Search

Page 291 of 399 (3985 items) « First ... < Previous 289 290 291 292 293 Next > ... Last »
  • Re: beogram 6006 problem

    Check the adjustments of the << and >> keys. It's mentioned in the service manual and is just about the only thing that can cause this fault. Martin
    Posted to BeoGram (Forum) by Dillen on 12-01-2008
  • Re: BM6000 Volume Dial Light

    The lamp is soldered in. Martin
    Posted to The Workbench (Forum) by Dillen on 11-28-2008
  • Re: Congratulations Keith!

    Martin
    Posted to General Forum (Forum) by Dillen on 11-28-2008
  • Re: Beomaster 2400

    No problem in wallmounting it. I have a BM1900 on the wall in my kitchen and it's basically the same machine. The only thing is the top lid, in most cases it will not close fully but stop apprx 1mm short. It will hold close though if pushed the last mm. Two screws in the wall and just hang the Beomaster. Martin
    Posted to General Forum (Forum) by Dillen on 11-28-2008
  • Re: Beomaster 5500 quirk

    Sounds like a capacitor problem. In this case, I would concentrate on the smaller caps in the power supply area and the caps on the processor module. It's the control signals from the processor that goes through to the signal path. Martin
    Posted to Vintage Products (Forum) by Dillen on 11-27-2008
  • Re: BeoCord 5500 auto-reversing when it shouldn't

    Well, my initial thought was about the 120 minute cassette tape. C-120 tapes are widely known to cause trouble in even the best decks simply because the tape is incredibly thin and I wouldn't expect any machine to accept them, some cassettedeck producers even advice against their use. I am not sure how the Beocord 5500 tells when to flip over but
    Posted to General Forum (Forum) by Dillen on 11-26-2008
  • Re: BeoCord 5500 auto-reversing when it shouldn't

    Belts are available but I would try another tape before anything else. Martin
    Posted to General Forum (Forum) by Dillen on 11-26-2008
  • Re: beogram 6006 problem

    wongss; Sounds like the optical tracking sensor (at the base of the carriage) is faulty, probably a burned lamp - or the interrupter is badly adjusted. chrisbou; Sounds like you are closing in on the problem. The voltage seems fine and the slow rotation of the motor to get the carriage to the exact drop spot is correct, we just have to get the threaded
    Posted to BeoGram (Forum) by Dillen on 11-26-2008
  • Re: beogram 6006 problem

    When the tonearm halts, try removing the belt without disturbing the position of the opto interrupter and watch the motor. If it rotates, the tonearm carriage doesn't move freely enough. Clean the threaded shaft and the nylon bushing under the carriage. Add a little fresh silicone grease and it'll be fine. These Beograms count pulses, it's
    Posted to BeoGram (Forum) by Dillen on 11-25-2008
  • Re: Beocord 7000 CD

    Velkommen til Beoworld ! Du kan skifte en laser hvis du har det nødvendige måleudstyr, justerings- og test cd'er osv. og kan finde en passende reservedel. Intet af det, er noget de fleste "bare lige" kan. Med andre ord - det er et job for een, der har lidt erfaring og råder over det nødvendige udstyr. Beocord
    Posted to BeoWorld Nordic (Forum) by Dillen on 11-24-2008
Page 291 of 399 (3985 items) « First ... < Previous 289 290 291 292 293 Next > ... Last »