in Search
Untitled Page

ARCHIVED FORUM -- April 2007 to March 2012
READ ONLY FORUM

This is the first Archived Forum which was active between 17th April 2007 and 1st March February 2012

 

Browse Forum Posts by Tags

Showing related tags and posts for the The Workbench forum. See all tags in the site
All Tags » technical (RSS)
  • Front Panel Fonts

    I am working on restoring a Beomaster 1700 amp, and would like to be able to be able to repair damage to the printing on the slider controls and front panel. What fonts did B&O use in their designs, and do members have any recommendations or tips for restoring damaged front panels? It seems to be...
    Posted to The Workbench (Forum) by ormej01 on 01-11-2012
  • Beolab 2500 - Voltage Problem

    Hi Guys, I've just joined and am starting off with problems !!! - I have inherited a pair of Beolab 2500 speakers, but they are set for 120V and not for 240V supply - I've been doing a bit of reading on this forum and there are some posts which say that the transformer can deal with both inputs...
    Posted to The Workbench (Forum) by Crawford on 12-18-2011
  • No power from my Beolab 7 speaker to my TV

    After searching the forum I could not find an answer to what seems like a small and simple problem, so here it is: I changed my Beolab 7-1 for a 7-4 (because in surround setup I think it sound much better). Upon installing I noticed the power out socket on the back of my new 7-4 was covered with some...
    Posted to The Workbench (Forum) by nv on 08-02-2011
  • BEOVISION MX 5500 (3251) Multiple Problems?

    Hi, I have a BEOVISION MX 5500 (3251) That is having multiple problems? I juts picked up a car load of older B&O stuff from a Beophile downsizing and this was in the mix. I live in the USA and am trying to connect the TV to an over the air Digital TV box. I have tried to connect it through the co...
    Posted to The Workbench (Forum) by Veloseller1 on 03-09-2010
  • Using PowerLink to control nonB&O amps

    Hi I came accross something in the Beotech website (http://www.beoworld.org/beotech/circuit.htm) showing how to use pin 4 in the powerlink to switch on a relay attached to a nonB&O subwoofer. I would like to do something similar until I can save up enough for some Beolab 9s, I have a BeoCenter2....
    Posted to The Workbench (Forum) by jamescumming on 12-04-2009
  • Need help with Beocenter AV5 will not enter the MENU

    Hallo, I need help. I bought some Beocenter AV5 from a hotel here in Stockholm where they said to me that device makers are ordinary consumer TV, s but now it appeared that it did not come in (Menu) via remote control, could someone tell me why I can not may come into menu? Are they perhaps the hotel...
    Posted to The Workbench (Forum) by BegBeo on 05-05-2009
  • Beocenter 5000 cassette deck

    Hi everyone Posting this in the hope that it helps other people out. I picked up a Beocenter 5000 a few weeks ago, the cassette deck would play and rewind okay but not fast forward. After digging around various threads I finally plucked up the courage to remove the deck from the unit and pull it down...
    Posted to The Workbench (Forum) by Andrew on 03-30-2009
  • Bang & Olufsen Red Line Authentic DIY ABR (Auxiliary Bass Radiators) Successful Repair

    Design concept failure As we all know, after about 15 or so years the foam used in B&O & many other manufacturers speakers turns to mush, cones fall away, speakers become seemingly useless. A market has arisen providing a readily available supply of replacement foam rubber rings, and appropriate...
    Posted to The Workbench (Forum) by BeoMatt on 03-11-2009
  • Redline 45.2 Bass unit and Wall brackets

    I am currently working on a pair of Redline 45.2 speakers. The on of them sounds fine but the other sounds like crap. When I opened them I noticed that the bass unit wass replaced by another (not B&O) in the one sounding like crap. Is it possible to get replacement units for those speakers anywhere...
    Posted to The Workbench (Forum) by madskp on 01-04-2009
  • Downgrade MX7000 software

    In order to have two way communication between my MX7000 and my Beolink7000 I need to downgrade my MX7000 software (which is a 4.3 version) to 1.something. As far as I can understand such a downgrade consists of nothing more than changing an IC in the MX7000. However, some questions comes to mind: 1...
    Posted to The Workbench (Forum) by chr_elling on 11-24-2008
Page 1 of 2 (18 items) 1 2 Next >